p.243ii) ANSI standard S12.55-2006/ISO3745:2003 may be used as a reference
p.244D. Allow UUT to stabilize and verify by taking light output measurements every minute
p.243document for other aspects of the measurements (calibration, etc.).
p.244until consecutive measurements are no more than 0.5% apart, utilizing previously recorded UUT stabilization time or verify by mathematical means that the lamp is stabilized.
p.243C. Reserved
p.243D. Low Voltage UUTs
p.244E. Record noise readings as specified in Section 8.8.4.E from measurement equipment
p.2431. UUTs designed for operation on low voltage transformers shall be operated on a compatible transformer specified or supplied by the lamp manufacturer.
p.244about the UUT to determine the peak sound level in dBA. This is the noise at the MaxLO.
p.2432. Electrical measurements shall include characteristics of the UUT.
p.244F. Adjust dimmer so that the light output is the lower of:
p.243E. Measurements:
p.2441. 20% of the MaxLO ± 5%; or
p.2431. The following data shall be collected at each measurement point:
p.2442. The minimum dimming level claimed as a percentage of the MaxLO ± 5%.
p.243i) Light output.
p.244G. Allow UUT to stabilize and verify by taking light output measurements every minute
p.244until consecutive measurements are no more than 0.5% apart, utilizing previously recorded UUT stabilization time or verify by mathematical means that the lamp is stabilized.
p.243ii) Peak Noise Reading.
p.243iii) Microphone Position at which the Peak Noise Reading occurs (e.g., 0 degrees /
p.243opposite lamp base).
p.244H. Verify that the UUT light output is still within the range in F).
p.243JA8.8.5 Test Procedure for Products Claiming Dimmability
p.2441. If not, repeat step A) and G).
p.2442. If light output is within range, record noise readings as specified in Section 8.8.4.E from measurement equipment about the UUT to determine the peak sound level in dBA. This is the noise at MinLO.
p.243JA8.8.5.1 General Test Procedures for Noise at Baseline output:
p.243A. Install the UUT in the test environment without a dimmer in the circuit.
p.244I. Repeat step A thru H as specified in JA8.8.5.2 for each dimmer to be tested. A test
p.243B. Set power supply to rated voltage and frequency of the device. If a range is specified,
p.243test sample at the midpoint of the range.
p.244setup that includes a device that allows hot switching between dimmers may be utilized to bypass stabilization time.
p.243C. Record noise readings from measurement equipment to determine sound level in
p.243dBA. This is the control noise level.
p.243D. Apply rated voltage/frequency to the device.
p.243E. Allow UUT to stabilize per IES LM-79 as applicable. If lamp has been stabilized for
p.243measurements previously and the stabilization time recorded, the lamp may be considered stabilized after operating for this period of time.
p.243F. Record noise readings as specified in Section 8.8.4.E from measurement equipment
p.243about the UUT to determine the peak sound level in dBA. This is the noise at the Baseline Light Output (BLO).
p.243G. If using a single microphone, note the position with the highest sound level (if
p.243applicable).
p.243H. Remove power from UUT.
p.243JA8.8.5.2 General Test Procedures for Noise on a Dimmer
p.243A. Install dimmer into the UUT test circuit. The dimmer shall be located outside of the
p.243sound chamber.
p.243B. Apply rated voltage/frequency to the dimmer or control device.
p.243C. Adjust dimmer to the maximum control position.
p.243Appendix JA8 – Qualification Requirements for High Luminous Efficacy Light Sourcesp.244
p.244Appendix JA8 – Qualification Requirements for High Luminous Efficacy Light Sources